kw2xrf.h File Reference
Interface definition for the kw2xrf driver. More...
Detailed Description
Interface definition for the kw2xrf driver.
Definition in file kw2xrf.h.
#include <stdint.h>#include "board.h"#include "periph/spi.h"#include "periph/gpio.h"#include "net/netdev.h"#include "net/netdev/ieee802154.h"#include "net/gnrc/nettype.h"#include "thread.h"
Include dependency graph for kw2xrf.h: This graph shows which files directly or indirectly include this file:Go to the source code of this file.
Data Structures | |
| struct | kw2xrf_params |
| Struct holding all params needed for device initialization. More... | |
| struct | kw2xrf_t |
| Device descriptor for KW2XRF radio devices. More... | |
Macros | |
| #define | KW2XRF_MAX_PKT_LENGTH (IEEE802154_FRAME_LEN_MAX) |
| Maximum packet length. | |
| #define | KW2XRF_DEFAULT_CHANNEL (CONFIG_IEEE802154_DEFAULT_CHANNEL) |
| Default channel used after initialization. | |
| #define | KW2XRF_DEFAULT_TX_POWER (CONFIG_IEEE802154_DEFAULT_TXPOWER) |
| Default TX_POWER in dbm used after initialization. | |
| #define | KW2XDRF_OUTPUT_POWER_MAX (8) |
| Maximum output power of the kw2x device in dBm. | |
| #define | KW2XDRF_OUTPUT_POWER_MIN (-35) |
| Minimum output power of the kw2x device in dBm. | |
Typedefs | |
| typedef struct kw2xrf_params | kw2xrf_params_t |
| Struct holding all params needed for device initialization. | |
Functions | |
| void | kw2xrf_setup (kw2xrf_t *dev, const kw2xrf_params_t *params) |
| Setup an KW2XRF based device state. More... | |
| int | kw2xrf_init (kw2xrf_t *dev, gpio_cb_t cb) |
| Initialize the given KW2XRF device. More... | |
| void | kw2xrf_reset_phy (kw2xrf_t *dev) |
| Configure radio with default values. More... | |
Allowed range of channels | |
| #define | KW2XRF_MIN_CHANNEL (11U) |
| #define | KW2XRF_MAX_CHANNEL (26U) |
| #define | KW2XRF_OPT_SRC_ADDR_LONG (NETDEV_IEEE802154_SRC_MODE_LONG) |
| Internal device option flags. More... | |
| #define | KW2XRF_OPT_RAWDUMP (NETDEV_IEEE802154_RAW) |
| legacy define | |
| #define | KW2XRF_OPT_ACK_REQ (NETDEV_IEEE802154_ACK_REQ) |
| legacy define | |
| #define | KW2XRF_OPT_AUTOCCA (0x0100) |
| CCA before TX active. | |
| #define | KW2XRF_OPT_PROMISCUOUS (0x0200) |
| promiscuous mode active | |
| #define | KW2XRF_OPT_PRELOADING (0x0400) |
| preloading enabled | |
| #define | KW2XRF_OPT_TELL_TX_START (0x0800) |
| notify MAC layer on TX start | |
| #define | KW2XRF_OPT_TELL_TX_END (0x1000) |
| notify MAC layer on TX finished | |
| #define | KW2XRF_OPT_TELL_RX_START (0x2000) |
| notify MAC layer on RX start | |
| #define | KW2XRF_OPT_TELL_RX_END (0x4000) |
| notify MAC layer on RX finished | |
| #define | KW2XRF_OPT_AUTOACK (0x8000) |
| enable automatically ACK for incommint packet | |
