syscfg_uwb_dw1000.h File Reference
uwb-dw1000 module configurations taken from decawave-uwb-dw1000/hw/drivers/uwb/uwb_dw1000 More...
Detailed Description
uwb-dw1000 module configurations taken from decawave-uwb-dw1000/hw/drivers/uwb/uwb_dw1000
Definition in file syscfg_uwb_dw1000.h.
This graph shows which files directly or indirectly include this file:Go to the source code of this file.
Macros | |
| #define | MYNEWT_VAL_UWB_DW1000_API_CHECKS (1) |
| Used to check that the UWB_DEV has been setup correctly at compile time. More... | |
| #define | MYNEWT_VAL_DW1000_HAL_SPI_BUFFER_SIZE (256) |
| Size of spi read/write buffer, sets the maximum allowed nonblocking read operation. | |
| #define | MYNEWT_VAL_DW1000_HAL_SPI_MAX_CNT (1024) |
| The maximum number of bytes in a single transfer that the SPI hardware supports. More... | |
| #define | MYNEWT_VAL_DW1000_DEVICE_SPI_RD_MAX_NOBLOCK (9) |
| Max size spi read in bytes that is always done with blocking io. More... | |
| #define | MYNEWT_VAL_DW1000_BIAS_CORRECTION_ENABLED (0) |
| Enable range bias correction polynomial. | |
| #define | MYNEWT_VAL_DW1000_DEVICE_TX_PWR (((float)-14.3f)) |
| Tx Power dBm. | |
| #define | MYNEWT_VAL_DW1000_DEVICE_ANT_GAIN (((float)1.0f)) |
| Antenna Gain dB. | |
| #define | MYNEWT_VAL_DW1000_RXTX_LEDS (1) |
| Enable showing rx and tx activity on leds. | |
| #define | MYNEWT_VAL_DW1000_RXTX_GPIO (0) |
| Enable showing rx and tx activity on gpios. | |
| #define | MYNEWT_VAL_DW1000_RNG_INDICATE_LED (0) |
| Toggle LED_1 for every range packet received. | |
| #define | MYNEWT_VAL_DW1000_CLI_EVENT_COUNTERS (0) |
| Expose event counter cli api. | |
Macro Definition Documentation
◆ MYNEWT_VAL_DW1000_DEVICE_SPI_RD_MAX_NOBLOCK
| #define MYNEWT_VAL_DW1000_DEVICE_SPI_RD_MAX_NOBLOCK (9) |
Max size spi read in bytes that is always done with blocking io.
Reads longer than this value will be done with non-blocking io.
- Note
- Ignore in RIOT since non-blocking SPI is not yet enabled
Definition at line 64 of file syscfg_uwb_dw1000.h.
◆ MYNEWT_VAL_DW1000_HAL_SPI_MAX_CNT
| #define MYNEWT_VAL_DW1000_HAL_SPI_MAX_CNT (1024) |
The maximum number of bytes in a single transfer that the SPI hardware supports.
- Note
- RIOT spi implementation will take care of splitting if this max value is exceeded. If asynchronous (non-blocking) spi is ever added to RIOT this value will need to be adapted to the platform specific value.
Definition at line 55 of file syscfg_uwb_dw1000.h.
◆ MYNEWT_VAL_UWB_DW1000_API_CHECKS
| #define MYNEWT_VAL_UWB_DW1000_API_CHECKS (1) |
Used to check that the UWB_DEV has been setup correctly at compile time.
- Note
- (UWB_DEV_RXDIAG_MAXLEN > 19)
Definition at line 34 of file syscfg_uwb_dw1000.h.
