periph_conf.h File Reference

Peripheral MCU configuration for Espressif ESP-WROVER-KIT V3. More...

Detailed Description

Peripheral MCU configuration for Espressif ESP-WROVER-KIT V3.

The Espressif ESP-WROVER-KIT is a development board that uses the ESP32-WROVER module which includes a built-in 4 MByte SPI RAM. Most important features of the board are

• Micro-SD card interface
• OV7670 camera interface
• 3.2" SPI LCD panel
• RGB LED

Furthermore, many GPIOs are broken out for extension. The USB bridge based on FDI FT2232HL provides a JTAG interface for debugging through the USB interface.

When the camera module is connected, add

USEMODULE += esp32_wrover_kit_camera

to the makefile of the application to use the according default board configuration.

For detailed information about the configuration of ESP32 boards, see section Common Peripherals.

Note

Most definitions can be overridden by an application-specific board configuration.

Author

Gunar Schorcht gunar.nosp@m.@sch.nosp@m.orcht.nosp@m..net

Definition in file periph_conf.h.

#include <stdint.h>
#include "periph_conf_common.h"

Include dependency graph for periph_conf.h:

Go to the source code of this file.

ADC and DAC channel configuration
#define	ADC_GPIOS   { GPIO34, GPIO35, GPIO36, GPIO39 }
	Declaration of GPIOs that can be used as ADC channels. More...
#define	DAC_GPIOS   { }
	Declaration of GPIOs that can be used as DAC channels. More...

I2C configuration
Note The GPIOs listed in the configuration are only initialized as I2C signals when module perpih_i2c is used. Otherwise they are not allocated and can be used for other purposes.
#define	I2C0_SPEED   I2C_SPEED_FAST
	I2C bus speed of I2C_DEV(0)
#define	I2C0_SCL   GPIO27
	SCL signal of I2C_DEV(0) [UEXT1].
#define	I2C0_SDA   GPIO26
	SDA signal of I2C_DEV(0) [UEXT1].

PWM channel configuration
LEDs are used as PWM channels for device PWM_DEV(0). Note As long as the according PWM device is not initialized with function pwm_init, the GPIOs declared for this device can be used for other purposes. As long as the according PWM device is not initialized with the pwm_init, the GPIOs declared for this device can be used for other purposes.
#define	PWM0_GPIOS   { GPIO0, GPIO4 }
	only available when camera is not connected
#define	PWM1_GPIOS   { }
	PWM_DEV(1) is not used.

SPI configuration
SPI configuration depends on configured/connected components. HSPI is is always available and therefore used as SPI_DEV(0) VSPI is only available when the camera is not plugged.
#define	SPI0_CTRL   HSPI
	HSPI is configured as SPI_DEV(0)
#define	SPI0_SCK   GPIO14
	SD Card SCL.
#define	SPI0_MOSI   GPIO15
	SD Card MOSI.
#define	SPI0_MISO   GPIO2
	SD Card MISO.
#define	SPI0_CS0   GPIO13
	SD Card CS.
#define	SPI1_CTRL   VSPI
	When the camera is not connected, VSPI is configured and becomes SPI_DEV(1). More...
#define	SPI1_SCK   GPIO19
	VSPI SCK used as LCD SCL, can be used to connect peripherals.
#define	SPI1_MOSI   GPIO23
	VSPI MOSI used as LCD MOSI, can be used to connect peripherals.
#define	SPI1_MISO   GPIO25
	VSPI MISO used as LCD MISO, can be used to connect peripherals.
#define	SPI1_CS0   GPIO22
	VSPI CS0 used as LCD CS, can be used to connect peripherals.

UART configuration
ESP32 provides 3 UART interfaces at maximum: UART_DEV(0) uses fixed standard configuration. UART_DEV(1) is not available. UART_DEV(2) is not available.
#define	UART0_TXD   GPIO1
	direct I/O pin for UART_DEV(0) TxD, can't be changed
#define	UART0_RXD   GPIO3
	direct I/O pin for UART_DEV(0) RxD, can't be changed

Macro Definition Documentation

ADC_GPIOS

#define ADC_GPIOS   { GPIO34, GPIO35, GPIO36, GPIO39 }

Declaration of GPIOs that can be used as ADC channels.

When the camera is connected there are no GPIOs left that could be used as ADC channels.

Note

As long as the GPIOs listed in ADC_GPIOS are not initialized as ADC channels with the adc_init function, they can be used for other purposes.

Definition at line 71 of file periph_conf.h.

DAC_GPIOS

#define DAC_GPIOS   { }

Declaration of GPIOs that can be used as DAC channels.

ESP-WROVER-KIT has no GPIOs left that might be used as DAC channels.

Definition at line 83 of file periph_conf.h.

SPI1_CTRL

#define SPI1_CTRL   VSPI

When the camera is not connected, VSPI is configured and becomes SPI_DEV(1).

Note

The GPIOs listed in the configuration are first initialized as SPI signals when the corresponding SPI interface is used for the first time by either calling the spi_init_cs function or the spi_acquire function. That is, they are not allocated as SPI signals before and can be used for other purposes as long as the SPI interface is not used.

Definition at line 178 of file periph_conf.h.