CC2538DK

Support for the Texas Instruments CC2538DK board. More...

Detailed Description

Support for the Texas Instruments CC2538DK board.

Overview

The CC2538DK is Texas Instruments' developer kit for the CC2538 SoC MCU, which combines an ARM Cortex-M3 microcontroller with an IEEE802.15.4 radio.

Hardware

cc2538dk

MCU CC2538SF53
Family ARM Cortex-M3
Vendor Texas Instruments
RAM 32KiB
Flash 512KiB
Frequency 32MHz
FPU no
Timers 4
ADCs 1x 12-bit (8 channels)
UARTs 2
SPIs 2
I2Cs 1
Vcc 2V - 3.6V
Datasheet Datasheet (pdf file)
Reference Manual Reference Manual

Flashing and Debugging

By default, RIOT will attempt to flash the MCU via the USB UART using a Python script named cc2538-bsl. Hold down the SELECT pushbutton while pressing RESET to activate the MCU's internal bootloader, then run:

make flash

Activating this bootloader is NOT enabled if the flash content is in factory default state (e.g. after unboxing). To set the bits in the CCA accordingly you have to follow the guidelines found here. To manage this first time access you have to download the "Uniflash" tool at TI's website.

Some Linux machines may not recognize the CC2538DK's vendor and product ID automatically. If a /dev/ttyUSBx device does not appear, try specifying these codes to the FTDI driver manually:

echo 0403 a6d1 > /sys/bus/usb-serial/drivers/ftdi_sio/new_id

If the path /sys/bus/usb-serial/drivers/ftdi_sio/ doesn't exist, you also have to load the module ftdi_sio by hand. Alternatively, you can install a udev rule that configures this on device connection, see this post on TI's E2E site for details.

RIOT will use /dev/ttyUSB1 by default, but if the UART is given a different device name, you can specity it to RIOT using the PORT variable:

make PORT=/dev/ttyUSB2 flash

To flash using a Segger JLink JTAG adapter you need to install Segger's JLinkExe tool, then specify PROGRAMMER=jlink when flashing:

make PROGRAMMER=jlink flash

Mac OSX <strong>El Capitan</strong> users

Be prevented that you'll need to disable Apple's System Integrity Protection to allow FTDI unsigned drivers to be loaded on your Mac.

To do this, reboot in recovery mode, by pressing simultaneously cmd + R while booting. Then, on the recovery mode go to Utilities/Terminal and type:

# csrutil status

If you see something like:

System Integrity Protection status: enabled.

You should disable it by typing:

# csrutil disable

then reboot

# reboot

and be sure that your System Integrity Protection is disabled

$ csrutil status
System Integrity Protection status: disabled.

Afterwards you'll be able to install this driver.

If everything goes OK reboot your Mac and then edit /System/Library/Extensions/FTDIUSBSerialDriver.kext/Contents/Info.plist with a text editor. Add the following block somewhere under IOKitPersonalities:

<key>TI_XDS100v3</key>
<dict>
<key>CFBundleIdentifier</key>
<string>com.FTDI.driver.FTDIUSBSerialDriver</string>
<key>IOClass</key>
<string>FTDIUSBSerialDriver</string>
<key>IOProviderClass</key>
<string>IOUSBInterface</string>
<key>bConfigurationValue</key>
<integer>1</integer>
<key>bInterfaceNumber</key>
<integer>1</integer>
<key>idProduct</key>
<integer>42705</integer>
<key>idVendor</key>
<integer>1027</integer>
</dict>

Reboot again and then type:

$ sudo kextload /System/Library/Extensions/FTDIUSBSerialDriver.kext

If everything worked, the XDS will be enumerated as /dev/tty.usbserial-<serial-number>

Files

file  board.h
 
file  periph_conf.h
 Peripheral MCU configuration for the CC2538DK board.
 
netdev::driver
const struct netdev_driver * driver
ptr to that driver's interface.
Definition: netdev.h:303
disabled
@ disabled
disabled
Definition: cc2538_rf.h:251