Files | Functions
HamiltonIoT Hamilton
Boards

Support for the HamiltonIoT Hamilton board. More...

Detailed Description

Support for the HamiltonIoT Hamilton board.

Files

file  board.h
 Board specific definitions for the Hamilton board.
 
file  gpio_params.h
 Board specific configuration of direct mapped GPIOs.
 
file  periph_conf.h
 Configuration of CPU peripherals for the Hamilton mote.
 

Functions

void board_init (void)
 Initialize board specific hardware, including clock, LEDs and std-IO.
 

xtimer configuration

#define XTIMER_DEV   TIMER_DEV(1)
 
#define XTIMER_CHAN   (0)
 

AT86RF233 configuration

#define AT86RF2XX_PARAM_SPI   SPI_DEV(0)
 
#define AT86RF2XX_PARAM_SPI_CLK   SPI_CLK_5MHZ
 
#define AT86RF2XX_PARAM_CS   GPIO_PIN(PB, 31)
 
#define AT86RF2XX_PARAM_INT   GPIO_PIN(PB, 0)
 
#define AT86RF2XX_PARAM_SLEEP   GPIO_PIN(PA, 20)
 
#define AT86RF2XX_PARAM_RESET   GPIO_PIN(PB, 15)
 

LED pin definitions and handlers

#define LED0_PIN   GPIO_PIN(0, 19)
 
#define LED0_PORT   PORT->Group[0]
 
#define LED0_MASK   (1 << 19)
 
#define LED0_ON   (LED0_PORT.OUTCLR.reg = LED0_MASK)
 
#define LED0_OFF   (LED0_PORT.OUTSET.reg = LED0_MASK)
 
#define LED0_TOGGLE   (LED0_PORT.OUTTGL.reg = LED0_MASK)
 

Button pin definitions

#define BTN0_PORT   PORT->Group[0]
 
#define BTN0_PIN   GPIO_PIN(0, 18)
 
#define BTN0_MODE   GPIO_IN_PU
 

FXOS8700 configuration

Note that another fxos8700 operation option, CONFIG_FXOS8700_USE_ACC_RAW_VALUES, need to be set according to the application purposes

#define FXOS8700_PARAM_I2C   I2C_DEV(0)
 
#define FXOS8700_PARAM_ADDR   (0x1E)
 
#define FXOS8700_PARAM_RENEW_INTERVAL   (1000000ul)
 

HDC1080 configuration

#define HDC1000_PARAM_I2C   I2C_DEV(0)
 
#define HDC1000_PARAM_ADDR   (0x40)
 
#define HDC1000_PARAM_RES   HDC1000_14BIT
 
#define HDC1000_PARAM_RENEW_INTERVAL   (1000000ul)
 

EKMB (PIR motion sensor) configuration

#define PIR_PARAM_GPIO   GPIO_PIN(PA, 6)
 
#define PIR_PARAM_ACTIVE_HIGH   (1)
 

PULSE_COUNTER configuration

#define PULSE_COUNTER_GPIO   BTN0_PIN
 
#define PULSE_COUNTER_GPIO_FLANK   GPIO_FALLING
 

TMP006 configuration

Note that two other tmp006 operation options, TMP006_USE_LOW_POWER and TMP006_USE_RAW_VALUES, need to be set according to the application purpose

#define TMP006_PARAM_I2C   I2C_DEV(0)
 
#define TMP006_PARAM_ADDR   (0x44)
 
#define TMP006_PARAM_RATE   TMP006_CONFIG_CR_AS2