periph_conf.h

Go to the documentation of this file.

/*
 * Copyright (C) 2015 TriaGnoSys GmbH
 *
 * This file is subject to the terms and conditions of the GNU Lesser
 * General Public License v2.1. See the file LICENSE in the top level
 * directory for more details.
 */
 
#ifndef PERIPH_CONF_H
#define PERIPH_CONF_H
 
/* This board provides an LSE */
#ifndef CONFIG_BOARD_HAS_LSE
#define CONFIG_BOARD_HAS_LSE    1
#endif
 
/* This board provides an HSE */
#ifndef CONFIG_BOARD_HAS_HSE
#define CONFIG_BOARD_HAS_HSE    1
#endif
 
#include "periph_cpu.h"
#include "clk_conf.h"
 
#ifdef __cplusplus
extern "C" {
#endif
 
static const timer_conf_t timer_config[] = {
    {
        .dev      = TIM2,
        .max      = 0x0000ffff,
        .rcc_mask = RCC_APB1ENR_TIM2EN,
        .bus      = APB1,
        .irqn     = TIM2_IRQn
    },
    {
        .dev      = TIM3,
        .max      = 0x0000ffff,
        .rcc_mask = RCC_APB1ENR_TIM3EN,
        .bus      = APB1,
        .irqn     = TIM3_IRQn
    }
};
 
#define TIMER_0_ISR         isr_tim2
#define TIMER_1_ISR         isr_tim3
 
#define TIMER_NUMOF         ARRAY_SIZE(timer_config)
 
static const uart_conf_t uart_config[] = {
    {
        .dev        = USART2,
        .rcc_mask   = RCC_APB1ENR_USART2EN,
        .rx_pin     = GPIO_PIN(PORT_A, 3),
        .tx_pin     = GPIO_PIN(PORT_A, 2),
        .bus        = APB1,
        .irqn       = USART2_IRQn
    },
    {
        .dev        = USART1,
        .rcc_mask   = RCC_APB2ENR_USART1EN,
        .rx_pin     = GPIO_PIN(PORT_A, 10),
        .tx_pin     = GPIO_PIN(PORT_A, 9),
        .bus        = APB2,
        .irqn       = USART1_IRQn
    },
    {
        .dev        = USART3,
        .rcc_mask   = RCC_APB1ENR_USART3EN,
        .rx_pin     = GPIO_PIN(PORT_B, 11),
        .tx_pin     = GPIO_PIN(PORT_B, 10),
        .bus        = APB1,
        .irqn       = USART3_IRQn
    }
};
 
#define UART_0_ISR          (isr_usart2)
#define UART_1_ISR          (isr_usart1)
#define UART_2_ISR          (isr_usart3)
 
#define UART_NUMOF          ARRAY_SIZE(uart_config)
 
#ifndef RTT_FREQUENCY
#define RTT_FREQUENCY       (16384)      /* in Hz */
#endif
 
static const i2c_conf_t i2c_config[] = {
    {
        .dev            = I2C1,
        .speed          = I2C_SPEED_NORMAL,
        .scl_pin        = GPIO_PIN(PORT_B, 8),
        .sda_pin        = GPIO_PIN(PORT_B, 9),
        .bus            = APB1,
        .rcc_mask       = RCC_APB1ENR_I2C1EN,
        .clk            = CLOCK_APB1,
        .irqn           = I2C1_EV_IRQn
    },
    {
        .dev            = I2C2,
        .speed          = I2C_SPEED_NORMAL,
        .scl_pin        = GPIO_PIN(PORT_B, 10),
        .sda_pin        = GPIO_PIN(PORT_B, 11),
        .bus            = APB1,
        .rcc_mask       = RCC_APB1ENR_I2C2EN,
        .clk            = CLOCK_APB1,
        .irqn           = I2C2_EV_IRQn
    }
};
 
#define I2C_0_ISR           isr_i2c1_ev
#define I2C_1_ISR           isr_i2c2_ev
 
#define I2C_NUMOF           ARRAY_SIZE(i2c_config)
 
static const spi_conf_t spi_config[] = {
    {
        .dev      = SPI1,
        .mosi_pin = GPIO_PIN(PORT_A, 7),
        .miso_pin = GPIO_PIN(PORT_A, 6),
        .sclk_pin = GPIO_PIN(PORT_A, 5),
        .cs_pin   = GPIO_UNDEF,
        .rccmask  = RCC_APB2ENR_SPI1EN,
        .apbbus   = APB2
    },
    {
        .dev      = SPI2,
        .mosi_pin = GPIO_PIN(PORT_B, 15),
        .miso_pin = GPIO_PIN(PORT_B, 14),
        .sclk_pin = GPIO_PIN(PORT_B, 13),
        .cs_pin   = GPIO_UNDEF,
        .rccmask  = RCC_APB1ENR_SPI2EN,
        .apbbus   = APB1
    }
};
 
#define SPI_NUMOF           ARRAY_SIZE(spi_config)
 
#ifdef __cplusplus
}
#endif
 
#endif /* PERIPH_CONF_H */