periph_conf.h

Go to the documentation of this file.

/*
 * Copyright (C) 2017 Freie Universität Berlin
 *               2017 Inria
 *               2017 HAW-Hamburg
 *               2018 Fundacion Inria Chile
 *
 * This file is subject to the terms and conditions of the GNU Lesser
 * General Public License v2.1. See the file LICENSE in the top level
 * directory for more details.
 */
 
#ifndef PERIPH_CONF_H
#define PERIPH_CONF_H
 
/* Add specific clock configuration (HSE, LSE) for this board here */
#ifndef CONFIG_BOARD_HAS_LSE
#define CONFIG_BOARD_HAS_LSE            1
#endif
 
#include "periph_cpu.h"
#include "clk_conf.h"
#include "cfg_i2c1_pb8_pb9.h"
#include "cfg_rtt_default.h"
#include "cfg_timer_tim2.h"
 
#ifdef __cplusplus
extern "C" {
#endif
 
static const uart_conf_t uart_config[] = {
    {
        .dev        = USART2,
        .rcc_mask   = RCC_APB1ENR1_USART2EN,
        .rx_pin     = GPIO_PIN(PORT_A, 3),
        .tx_pin     = GPIO_PIN(PORT_A, 2),
        .rx_af      = GPIO_AF7,
        .tx_af      = GPIO_AF7,
        .bus        = APB1,
        .irqn       = USART2_IRQn,
        .type       = STM32_USART,
        .clk_src    = 0, /* Use APB clock */
    },
    {
        .dev        = USART3,
        .rcc_mask   = RCC_APB1ENR1_USART3EN,
        .rx_pin     = GPIO_PIN(PORT_C, 11),
        .tx_pin     = GPIO_PIN(PORT_C, 10),
        .rx_af      = GPIO_AF7,
        .tx_af      = GPIO_AF7,
        .bus        = APB1,
        .irqn       = USART3_IRQn,
        .type       = STM32_USART,
        .clk_src    = 0, /* Use APB clock */
    }
};
 
#define UART_0_ISR          (isr_usart2)
#define UART_1_ISR          (isr_usart3)
 
#define UART_NUMOF          ARRAY_SIZE(uart_config)
 
static const pwm_conf_t pwm_config[] = {
    {
        .dev      = TIM3,
        .rcc_mask = RCC_APB1ENR1_TIM3EN,
        .chan     = { { .pin = GPIO_PIN(PORT_B, 4), .cc_chan = 0 },
                      { .pin = GPIO_PIN(PORT_C, 7), .cc_chan = 1},
                      { .pin = GPIO_PIN(PORT_C, 8), .cc_chan = 2},
                      { .pin = GPIO_PIN(PORT_C, 9), .cc_chan = 3} },
        .af       = GPIO_AF2,
        .bus      = APB1
    },
};
 
#define PWM_NUMOF           ARRAY_SIZE(pwm_config)
 
static const spi_conf_t spi_config[] = {
    {
        .dev      = SPI1,
        .mosi_pin = GPIO_PIN(PORT_A, 7),
        .miso_pin = GPIO_PIN(PORT_A, 6),
        .sclk_pin = GPIO_PIN(PORT_A, 5),
        .cs_pin   = GPIO_UNDEF,
        .mosi_af  = GPIO_AF5,
        .miso_af  = GPIO_AF5,
        .sclk_af  = GPIO_AF5,
        .cs_af    = GPIO_AF5,
        .rccmask  = RCC_APB2ENR_SPI1EN,
        .apbbus   = APB2
    },
};
 
#define SPI_NUMOF           ARRAY_SIZE(spi_config)
 
#ifdef __cplusplus
}
#endif
 
#endif /* PERIPH_CONF_H */